Interior

Three-part MagSafe phone holder that clips near the glove-box compartment on left-hand-drive interiors. Its position keeps the holder away from the gear lever and leather trim. It accepts a 46 mm-inner/54 mm-outer MagSafe-style magnet ring and the printed parts are joined with super glue.

Extended ball-socket connector for the exterior door-handle linkage, designed to add adjustment when the lever must be pulled too far or is difficult to reconnect. It uses an extra M5 nut; the creator prints it open-slot side up without supports at 0.2 mm layers and about 15% infill.

Two-piece passenger-side interior door-pull conversion with a GT3-like shape. The creator says to mirror the files for the opposite side and attach the pull strap with a small screw.

Replacement for the upper square CD-case storage unit in the dashboard, with a top cable-routing port for a USB/Bluetooth module. The creator printed it in resin and reports good fit.

Left and right interior door-handle shells that convert the 997 door release to a GT3-style fabric pull strap. The archive includes a combined pair and strengthened separate left/right versions.

Replacement hanger for a rear-door shade. The creator designed it for the 955/957 and notes that it leaves some visual gaps because it does not perfectly follow the door-trim shape, but remains functional; mirror the model for the opposite side.

Drop-in ashtray-delete cubby for the Boxster 986. The creator secured it with double-sided tape and finished it with black flexible interior paint.

Cup-holder mount for an Apple MagSafe second-generation 25 W charging puck with braided cable. The creator reports fit with an iPhone 16 Pro Max in a silicone case.

Replacement finger plate for an early interior door-release handle, modeled after degraded original trim during an upholstery restoration. The creator printed it in ABS for optional acetone smoothing and says PLA should also work.

Friction-fit tray variants create a second storage level in the seven-inch-deep center-armrest compartment: plain, tissue-box passthrough, and honeycomb versions, plus a STEP stencil for cutting surface liners. The installed tray sits just above five inches from the bottom, leaving room below for a cube tissue box; the creator had not test-printed the honeycomb variant.

Left- and right-side frames for fitting nearly any 4x6 speaker behind the factory HiFi grilles while retaining the stock grille appearance.

Two-piece glove-box CD-holder replacement that mounts two USB ports and provides a pull-out tray for SIM-card access. It assembles with three M3 screws; the updated drawer includes a retaining screw.

Two-piece platform for mounting an Apple MagSafe USB-C adapter in the 12 V smoker-package compartment below the shifter. The creator calls for a low-profile USB-C 12 V car adapter, automotive trim tape, and glue or epoxy for PLA.

Round push-in cover for an interior-trim screw opening, with the opening enlarged by the creator for the larger screws used in their installation.

Replacement front speaker grille for late-model 944 cars, modeled around Tref67's speaker spacer after the creator found both pieces missing.

Replacement end cap, catalogued as a sleeve, for the 914-6 manual-throttle rod. The creator recreated it from broken pieces of the original part and old-stock photographs.

Replacement set for the heater-panel slider levers, supplied as separate upper and lower STL models.

Cup holder with a 4-inch opening designed to fit the change-holder location; the creator contrasts it with an original 3-inch-opening version.

Clamp that adapts the creator-linked Amazon phone holder to mount on the side of the center console instead of an air vent.

Replacement shaft for the instrument-cluster trip and dimmer controls, measured from an OEM stalk. The creator recommends resin or ABS for resolution and heat resistance and notes that sanding may be needed for a close fit.

Ashtray-mounted phone stand with a USB cable pass-through for an adhesive magnetic charging puck, designed by Trogdor4Ever for the Cayenne 958 center console. The creator printed it in PLA+ and added neoprene foam to the lower corners for a snugger fit.

Printable lining for a center-console-delete conversion, supplied as a full model or front/rear split for a Prusa Mk3S-size bed, plus a cover plate. The creator recommends PETG, instructs removal of the orange bracket tabs for mounting, and leaves room to upholster the part.

Center-console phone mount based on the creator's 3D scan, with versions for iSetchi and Apple MagSafe chargers. The creator reports months of in-car use and says the Apple charger must be attached with double-sided tape or glue.

Three-part clip-in center-console coin tray that replaces the ashtray. The creator directs users to slide the parts together, glue the seams, and apply fabric tape at the sides to improve fit and reduce rattles.