@Razzmatazz

MagSafe Cupholder Phone Mount
Cupholder-mounted MagSafe phone stand for PDK interiors with the deeper cupholder slot. The creator recommends PLA+ or carbon-fiber PLA and states the design was tested only on the 992.2.

Electric sunroof latch
Replacement electric sunroof latch.

Large-Cup Console Adapter
Center-console cup-holder insert that supports larger drink containers; the creator strengthened later revisions after long-term use.

Interior Door Pull-Strap Conversion
Two-piece passenger-side interior door-pull conversion with a GT3-like shape. The creator says to mirror the files for the opposite side and attach the pull strap with a small screw.

Double-DIN Center Console
Replacement center-console assembly laid out for a double-DIN radio installation.

Center-Console MagSafe Charger Mount
Three-part MagSafe charger mount for a non-smoker center console. The holder and two legs friction-fit between the rear metal trim and front rubber lip, keep both cupholders and the parking brake accessible, and accept the creator-specified 2024 Apple 25 W MagSafe Charger with braided cable.
Remote Clutch Bleeder Bracket
Two-piece bracket that mounts a remote clutch bleed-screw assembly to the fan shroud. It is sized for a -3 AN bulkhead mount accepting a 3/8-24 bleeder screw and uses a removable end plate so the clutch line can be slid into place without disconnecting it.

Ashtray Phone Mount
Four-piece ashtray-insert phone mount for 2010-2016 970.1/970.2 cars, designed around the Asus ROG Phone II. The flexible base and wedge friction-fit in the ashtray while the rigid arm and body bolt together; installation uses no clips, adhesive, or vehicle modifications.

Back cover roller brackets
Replacement back cover roller brackets.

Ashtray Cupholder
Drop-in ashtray replacement with a removable cupholder insert.

Alternator Cooling Duct
Streamlined replacement alternator cooling duct modeled from a 3D scan of the original failure-prone part and shaped for support-free printing. The creator printed it in PA12 and reports that PETG has also been tested.



Washer-Fluid Filler Neck
Replacement windshield-washer reservoir filler neck supplied as a primary neck plus mounting bib, with an alternate split-neck version for smaller printers.

Door-Handle Insert Pair
Left and right replacement door-handle inserts designed to print face-down for a textured finish.

Hardtop Latch Mechanism Cap
Replacement cap for the Cabriolet hardtop-latch opening. The creator says it hides the latch mechanism, may need approximately 1% scale adjustment depending on printer accuracy, and should be printed flat-side down.

Ashtray Gooseneck Phone Mount
Gooseneck phone mount that fits snugly in the ashtray and provides an integrated 17 mm ball for a magnetic holder.

Engine Service Blanking-Plug Set
Temporary S2 engine-service plugs for the spark-plug tunnel, injector port and airflow-sensor hose opening.

Gauge-Ring Phone Mount
Phone mount that clips around an 82 mm dashboard gauge and accepts a WizGear magnetic holder.

Adjustable Clutch Pedal Stop
Adjustable clutch-pedal stop intended to reduce pedal travel. The creator specifies a 60 mm or 80 mm M10 hex-head bolt and nut, two 20 mm M4 bolts with nuts, four 12 mm washers, threadlocker, and PETG.

Door Pocket Mounting Bracket
Replacement mounting bracket for the interior door storage pocket, modeled for the creator's 1974 911.
Relay Board Cover
Printable replacement cover for the engine-bay relay board. The creator printed it in PLA with supports at 0.2 mm resolution and glued the oversized print after splitting it for a 210 × 210 mm bed.

Center-Console Twin Cup Holder
Single-piece center-console drink holder with two circular wells. The creator's photograph shows the physical print installed between the seats.

(88 Later) Sunroof Cam
Replacement (88 later) sunroof cam.
24 of 275 shown
